Difference between revisions of "Installation of PIONE"

Revision as of 07:14, 22 May 2017

Installation of PIONE

Introduction

　PIONE is based on ruby, gem, bundle. Check if ruby, gem, bundle have been installed。ruby should have a version number greater than or equla to 1.9.2. Versions and installed directories of ruby, gem, bundle can be checked as bellow. If Eos has been installed previously, they may be found under the Eos directory. If the directories are not the same, PIONE may have problems in installation and execution. It is recommended that they are in the same directory.

$ which ruby
/Eos/util/X86MAC64/bin/ruby
$ which gem
/Eos/util/X86MAC64/bin/gem
$ which bundle
/Eos/util/X86MAC64/bin/bundle
$ ruby -v
ruby 1.9.3p551 (2014-11-13 revision 48407) [x86_64-darwin12.5.0]
$ gem -v
1.8.23.2
$ bundle -v
Bundler version 1.7.7

If there are more than one ruby/gem, the unused versions should be deleted or renamed like gem1.9

Installation

When ruby/gem has been installed

　gem in ruby does work in the installation。Installation is done in the same directory as gem. When /usr/local or /sw/ are destinations, the administrator must do the installation.

$ gem install pione

　On update,

$ gem update pione

Installing directly from github

　Download POINE from github.

 $ git clone https://github.com/pione/pione.git

Update by bundle. 

Firstly, check if you have "bundle". If yes, you will see a line including bundle

$ which bundle
/Eos/util/X86MAC64/bin/bundle

Secondly, update bundle, if you have it. It is to be noted that the bundle install command is run in /pione, or

set its path beforehand (Gemfile, vender/bundle and files below it are necessary). 

$ cd pione
$ bundle install --path vender/bundle

Setting environment

　Run the following for defining variables of PATH and RUBYLIB.

$ cd ${PIONE_REP}
$ export PATH=$PWD/bin:$PATH
$ export RUBYLIB=$PWD/lib

　or running pione/misc/env.sh is able to set the environment.

　You may well have this setting to be performed after your shell starts, as in Setting environment of Eos.
　Those environment variables, and commands such as bundle install, are not needed on install.

Installation with PIONE Webclient, using a installation shell

The following commands can be used to start a shell for installation.

$ wget -q -O - https://raw.githubusercontent.com/pione/pione-webclient/master/install.sh | sh

If wget is not available, using curl,

$ curl https://raw.githubusercontent.com/pione/pione-webclient/master/install.sh | sh

　However, you need ruby/gem/bundler(ruby tool）for this. Install ruby/gem, if you have not. When gem has been installed, but not bundler, you can install using gem. You input the following beforehand.

$ sudo gem install bundler

The problem about install

　Currently, working on LINUX/OS-X is sure. But, There is problems on Windows, in relation to implementation of Ruby's Thread.

　In some environments, git/ruby/gem/bundle it may not have been installed git/ruby/gem/bundle and etc... .

　gitcan be installed in each environment (e.g. apt-get/yum). Most packages are supported.

　Currently, about the version of ruby is 1.9.2 of higher and 1.9-generations required. It is a plan that corresponds to the 2.1 in the future. If your LINUX corresponds only version 1.9 of ruby, you need to download the source code and install. Then, ZLIB/YAML is required. First install those, and next install configure/make/make of ruby.

　About gem, install it by downloading rubygems.

　bundle can be installed by gem.